Cabinet Hardware: How I Choose Sizes, Mix Knobs and Pulls, and Make It All Work
Cabinet hardware is often called the jewelry of the kitchen. Fair enough. But this jewelry also has to open the trash pull-out while you’re holding a cutting board covered in onion scraps. It needs to earn its place.
Here’s how I choose cabinet hardware sizes, mix knobs and pulls, and decide where a little decorative detail makes sense.

How big should cabinet hardware be?
There are two approaches I use. One is to choose a consistent pull size throughout the cabinetry. That repetition can create a clean, contemporary look.
My preference is usually to vary the size according to the drawer or door it opens. A little drawer and a tall pantry door have different proportions. Their handles can, too.
My starting point is the rule of thirds: I look for a pull approximately one-third the width of a drawer front or the height of a cabinet door. On a 30-inch-wide drawer, for example, I might start by considering a pull around 10 inches long.
It’s a visual guide, not a requirement to track down an oddly specific size. I adjust for the available hardware sizes, cabinet style, comfortable grip, and how the whole elevation looks together. Very tall doors may call for a different approach.
One ordering detail matters: overall length and center-to-center measurement are different. Overall length describes the full pull; center-to-center measures the distance between its mounting holes. Confirm both before ordering or drilling.
Why I usually put pulls on drawers
I generally prefer one centered pull on a drawer, especially a wide one. It gives your hand an obvious place to go and encourages a more even pull.
Two knobs can look lovely, but how often are you actually using both hands to open a drawer? Grabbing just one applies force off-center and can encourage twisting or racking, depending on the drawer construction and slide system. Good glides, proper installation, and appropriate stabilization matter, too.
For everyday use, I usually choose the centered handle. Pretty is wonderful. Pretty and easy to live with is the assignment.
Where I mix in knobs
Mixing knobs and pulls gives cabinetry some personality. I like knobs on the top tier of stacked upper cabinets, narrow drawer fronts with limited room for a pull, and selected base cabinet doors when the arrangement needs a little variety.
I also like knobs on cabinet doors beneath an island overhang, where I consider how the hardware projects into the seating area. Tall upper cabinet doors and wide drawers almost always get pulls.
I decide these placements while looking at the complete cabinet layout. The goal is a thoughtful rhythm, with each piece comfortable to reach and use.
My two-knob exception: the makeup drawer
A shallow makeup drawer at a seated vanity is one place I’ll often use two knobs. Positioned toward the sides, they leave the center clear where your body sits.
Nobody needs a handle poking them in the tummy while they’re trying to put on mascara. I still check the drawer construction and how it opens before making that choice.
Cup pulls: I have questions
Cup pulls are popular for a reason. They can be beautiful in a traditional kitchen. Personally, I don’t love reaching underneath something when I can’t see where my fingers are going.
I feel like a bug—or a mysterious deposit of peanut butter—is going to introduce itself at any moment.
That is my personal objection, not a universal design rule. I prefer an open pull that I can see, grip, and wipe clean.
Latches, without the daily obstacle course
I love the character of a cabinet latch. I’m less enthusiastic about having to twist and release one every time I need the dish soap.
My preference is a decorative, non-locking latch look, with the cabinet held closed separately as needed, so the door opens without operating a catch. I confirm the actual mechanism before specifying it.
A sink base or a selected upper cabinet in an office can be a lovely place for this detail. A little goes a long way.
Backplates can be pretty and practical
Backplates add another layer of shape, texture, and detail behind a knob or pull. Sometimes I choose them simply because they’re beautiful.
They can also be a godsend when updating existing cabinets. If the new hardware needs different hole spacing, a properly sized backplate may conceal the old holes while allowing new ones to be drilled.
Measure first. The plate needs to cover the old holes, the new mounting locations need to work, and the cabinet front still needs to support the installation. A backplate is helpful, but it isn’t magic.
Match the panel-ready appliances, too
When appliances are concealed behind cabinet panels, I prefer hardware that coordinates with the rest of the cabinetry. Some appliance brands offer their own handles, but I often choose coordinating appliance pulls from the cabinet hardware collection.
The important word is appliance. A long cabinet pull is not automatically suitable for a heavy refrigerator panel. I check the appliance manufacturer’s requirements, mounting details, and the hardware’s intended use.
That gives us a cohesive look with hardware chosen for the job it actually has to do.
Choose the hardware before the drill comes out
Size, placement, projection, and grip all deserve attention before installation. I like to see samples against the cabinet fronts and confirm that the choices work together across the room.
Planning a kitchen, bathroom, or cabinetry update? Kristine Krupa Interiors helps homeowners in Colorado Springs and beyond bring the layout, finishes, and details together. Get in touch to discuss your project—and let’s choose the hardware before someone starts making holes.




Comments